Infrastructure

Equipment

A look at the machines that run in our 42,600 square foot facility. We invest in capable equipment because our customers' programs do not tolerate underpowered tooling.

CNC Machining Centers

Our machining floor is built around Okuma and Mazak platforms — the workhorses of precision aerospace and defense manufacturing. The combination of multi-tasking and 5-axis simultaneous capability means we can handle complex geometry without multiple setups.

Okuma Multi-Tasking Center (9-axis)

Multiple

Simultaneous turning and milling in a single setup. Used for complex shafts, housings, and components that would otherwise require three or four separate machines.

Mazak 5-Axis Machining Center

3 units

Full 5-axis simultaneous machining. Handles impellers, aerospace structural components, and complex curved surfaces without repositioning.

Vertical Machining Centers (VMC)

Multiple

3-axis and 4-axis vertical mills for prismatic parts, plates, brackets, and high-volume production runs.

Horizontal Machining Centers (HMC)

Multiple

Pallet-based production machining for high-volume, consistent-cycle work.

CNC Turning Centers

Multiple

Bar-feed and chucking lathes for rotational parts, threaded components, and hydraulic fittings.

Facility photo: Machining floor — Okuma or Mazak in operation, chips flying

Fabrication Equipment

From raw plate to finished weldment, our fabrication equipment covers the full sheet metal and structural workflow.

Waterjet Cutting System

1 unit

Cuts virtually any material without heat-affected zone. Used for gaskets, titanium plate, armor steel, and non-metallic materials.

CNC Laser Cutter

1 unit

High-precision sheet metal cutting for mild steel, stainless, and aluminum plate up to 1" thick.

CNC Press Brake

Multiple

Precision bending with tooling for tight-radius and complex form work. Backed up by Delem CNC controllers.

CNC Punch / Turret Press

1 unit

High-speed punching for sheet metal panels, chassis, and enclosures.

Robotic Welding Cells

Multiple

MIG welding robots for consistent production weldments. Supervised by AWS-certified welders.

Facility photo: Fabrication area — waterjet, laser, or press brake in operation

Finishing & Coating

An on-site powder coat line and blast room means we control the finish quality and the schedule. Nothing leaves the facility for coating.

Powder Coat Line

1 line

Full manual and automated powder application with IR and convection cure oven. Pretreatment wash and blast bay upstream.

Blast Room

1 room

Abrasive blast cleaning for surface prep before coating. Also used for rust removal and pre-paint surface profiles.

Spray Booth

1 unit

Wet paint application for Mil-Spec epoxy primers and topcoats where powder coat is not specified.

Facility photo: Powder coat line — parts in cure oven or being sprayed

Quality & Inspection

Measurement is as important as manufacturing. Our inspection lab is equipped to verify every critical dimension before a part ships.

Faro Arm (Portable CMM)

1 unit

Six-axis articulating arm for in-process and in-fixture measurement. Can go to the part rather than requiring the part to come to the CMM.

Zeiss CMM

1 unit

Fixed coordinate measuring machine for high-accuracy final inspection of complex prismatic parts. Temperature-controlled inspection room.

Optical Comparator

1 unit

Profile projection for thread forms, radii, and 2D geometry verification.

Calibrated Hand Tools

Full set

Micrometers, calipers, depth gauges, thread gauges, surface roughness probes — all maintained on a calibration schedule.

Facility photo: Inspection lab — CMM or Faro Arm measuring a part

Electronics Manufacturing

PCB assembly and wire harness manufacturing require specialized equipment and a controlled environment. Our electronics area is separate from the machining floor.

SMT Pick-and-Place Line

1 line

Surface mount technology line for PCB assembly. Solder paste printer, pick-and-place, and reflow oven in sequence.

Selective Solder Machine

1 unit

For through-hole components on mixed-technology boards where wave solder would damage surface-mount parts.

AOI System

1 unit

Automated optical inspection after reflow to catch solder defects, missing components, and polarity errors.

Wire Harness Test Equipment

Multiple

Continuity testers, hi-pot testers, and crimp pull-force equipment for harness verification.

Facility photo: Electronics area — SMT line or wire harness assembly station

Facility Tour

Video: machining floor walkthrough

Video: fabrication and welding area

Video: electronics and assembly area

Have a complex part that has given other shops trouble?

Tell us about it. Our equipment and our people have seen most of it.

Start a Conversation